[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1042: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:1)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1042: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:1)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/session.php on line 1042: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:1)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4752: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:1)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4754: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:1)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4755: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:1)
[phpBB Debug] PHP Warning: in file [ROOT]/includes/functions.php on line 4756: Cannot modify header information - headers already sent by (output started at [ROOT]/config.php:1)
 Augustica.com • View topic - Desighning EL34 Push-Pull Amplifier

Desighning EL34 Push-Pull Amplifier

Discussion of tube based amplifier projects

Desighning EL34 Push-Pull Amplifier

Postby Augustica.com » 29 Sep 2013, 16:06

Schematic below shows a typical push-pull amplifier built with one 12AX7 and two EL34 tubes.

Image

Additional pairs of output tubes may be used but calculations remain the same. The output stage is fixed biased, but cathode biased amplifiers are usually fully cathode bypassed so treatment would also be the same. We will start with finding the open-loop gain from input to output before applying feedback. For a push-pull amplifier we can consider one half of the output stage when calculating gain.

Strictly speaking, because the pair of EL34 is not perfectly balanced, its gain will be different depending on which of its grids and anodes we consider. Nevertheless, for the sake of simplicity, we will assume the balance is fair and take the gain to one anode as a half the differential gain:

Image

R = R5 = R6 = 100KOhm || 220KOhm = 69KOhm
Ra = 65KOhm

Image

The voltage gain of each EL34 pentode is -GmZpri. The output transformer will usually be specified in terms of its anode-to-anode impedance, which might be 3.5KOhm for a pair of EL34, but we are only considering one half of the output stage. Assuming the output stage operates in class A or AB, the impedance seen by either tube is half the anode-to-anode impedance under small signal conditions.

From EL34 datasheet the Gm is about 10mA/V. Assuming this is a class AB amplifier with a 3.5KOhm output transformer, the magnitude of the gain of one side is:

Image

If feedback is taken from the 8Ohm speaker tap then we find the turns ratio to be:

Image

Thus, the voltage gain of the transformer is 1/20.9 = 0.048. The total open-loop voltage gain of the circuit is:

Image

If we aim for a feedback factor of 10dB, then the gain of the amplifier will be reduced by a factor of:

Image

Now we can find the feedback coefficient B by rearranging the universal feedback equation:

Image

In other words, for every volt of signal appearing at the speaker, 0.1 volts will be fed back to the phase inverter via the potential divider formed by R2 and R10 on the schematic above. Rearranging the formula for a potential divider to find R10 gives:

Image

The nearest standard resistor is 43KOhm. A variable resistor could be used to set the exact value to taste, and presence, resonance and variable feedback controls finally added.
Augustica.com
Site Admin
 
Posts: 118
Joined: 22 Jun 2013, 15:13

Return to Tube Amplifiers

Who is online

Users browsing this forum: No registered users and 1 guest


cron