FEATURES:
- Five inch (5”) (108x65mm) high resolution color display, 800x480 pixels and 24-bits colours.
- The final stage uses field effect (MOSFET) transistors type BLF188 from NXP, designed to withstand high mismatch (SWR) at the output and intended for operation in aerospace, industrial, mobile, and radio broadcast applications.
- Compatible with all transceiver models available on the market - does not need any special signals: “ground on transmit” (PTT) and 50W of RF drive power is sufficient to achieve the full rated output power.
- Broadband input circuit provides a perfect transceiver load with SWR below 1.2:1 (typically 1.1:1), without retuning throughout the whole frequency range from 1.8 to 54MHz.
- The overall operation of ACOM 1200S is extremely simple - the screen menus are intuitive and easy to follow and no special skill is required from the operator when changing frequency and bands.
- Possibility of automatic control when connected to a transceiver with a CAT interface. The amplifier monitors the transceiver constantly, duly follows the operating frequency, and changes the bands accordingly.
- Even if not connected with a CAT interface, the amplifier monitors the frequency of the input signal through the built-in frequency counter and automatically switches over the bands.
- The amplifier is remotely controlled by a RS232 interface.
- Takes care of itself during operation due to the continuously working protection circuits in all modes of operation.
- The operator can monitor digitally more than 10 parameters concerning the working regimes of the amplifier.
- Easy maintenance – detailed data (55 parameters) about each of the last 28 hard-fault protection trips is stored in the amplifier’s nonvolatile memory.
- Convenient for DXpeditions and field operation. Extremely compact and light construction, extended mains voltage range (93V÷265V), limited inrush current and purely sinusoidal consumed mains current, automatic Power Factor Correction (PFC) – all significant parameters in operation from unstable mains, generators etc., features achieved due to the built-in switching mode power supply (SMPS).
- Perfect electromagnetic compatibility (EMC) both with the highly sensitive as well as with the powerful appliances in the radio station (receivers, computers, more amplifiers) exceeding the standard EMC requirements due to the use of PFC and the built-in additional radio-frequency filters.
ACOM 1200S SPECIFICATIONS:
Rated Output Power: 1000W +/-0.5dB, PEP or continuous carrier (1200W typically).
Intermodulation Distortions (IMD3): better than 30dB below the rated PEP output power.
Harmonic & Parasitic Emissions Output Suppression: better than 60dB below the rated PEP output power (65dB typically).
Input & Output Impedances: nominal value: 50 Ohm unbalanced with UHF (SO239) type connectors
- Input circuit: broadband, SWR below 1.2:1 (1.1:1 typically); 1.8 – 54 MHz continuous range without retuning or switching
- RF by-pass path SWR - below 1.1:1, 1.8-54 MHz
- Admissible SWR at the output load (the antenna): up to 3:1 with proportional output power reduction and up to 1.5:1 for full output power.
RF Power Gain: 13dB +/-1dB
Mains Power Supply Voltage: 93V/265V without switching.
Mains Power Consumption at Full Output Power: 2000VA or less with a power factor of 0.95 or higher;
Mains Power Consumption in Low Energy (waiting) Mode: less than 1VA;
Complies with EU safety regulations and electromagnetic compatibility standards, as well as with the Industry Canada rules.
Operating Environment:
- Temperature range: -10 C to +40 C
- Relative air humidity: up to 95% @ 35 C
Dimensions (projections not included) & Operating Weight:
- 42 cm deep x 37 cm wide x 16 cm high, with weight of 12 kg.
All ACOM Amplifiers come with a two (2) year factory warranty.
If your ACOM product fails within the first 120 days, ACOM will prepay shipping to their warranty service center. Shipping will also be prepaid back from the repair center. This is an exclusive warranty for Augustica Technologies customers only and is the best warranty in the industry.
After 120 days and up to the end of the two (2) year warranty period, ACOM will require payment by the customer for shipping to their repair facility. Shipping will then be prepaid by ACOM for the return of the serviced amplifier. ACOM will repair or replace your unit at any time during the two (2) year warranty period.
Warranty Coverage for the tube or tubes in all ACOM amplifiers is one (1) year.